The ODROID-HC4-P KIT consists of an ODROID-HC4 board, a case made of a rigid PCB into which you can mount two 3.5-inch HDDs horizontally,and includes a cooling fan.

It’s a network storage device that you can build for yourself, and the existing HC4’s Petitboot function and latest OS versions are supported can be used without any changes. 


Please note - This KIT does NOT include OLED+RTC for HC4-P. This is available AT THIS LINK.





ACPU (Amlogic S905X3)H2x System LED indicators
BDDR4 memory (4GiB)I1x UART for system console
C2x SATA portsJ1x IR receiver
D1x RJ45 Ethernet port (10/100/1000)K5x GPIO pins (for optional OLED display)
E1x HDMI 2.0L1x Micro SD slot
F1x USB 2.0 host portM1x Cooling fan
G1x DC power jack (Outer diameter : 5.5mm, inner diameter 2.1mm)N1x Boot switch


Software Support


Petitboot can find the OS on an SD card, the HDD or the SSD. Even if you do not have an SD card but you have a plugged-in HDD or SSD that has an OS installed, Petitboot will fiond and boot the HC4 using the OS from the HDD or SSD. Debian/Ubuntu OS can run with either Hardkernel’s preinstalled OS image, or Debian/Ubuntu Netboot Installer - which you can obtain from the ODROID forum.


Supported Linux kernel versions:-


4.9.230 or newer (Hardkernel stock OS version)
Mainline kernel 5.15 or newer (Unofficial version from ODROID forum)


Specification


FORM FACTORBoard Dimensions: 84mm x 90.5mm x 25.0mm
Transformation KIT Dimensions : 225mm x 106mm x 127mm
Weight: 615g including board and transformation KIT without HDD
PROCESSORAmlogic S905X3 Processor
L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processorsQuad-Core Cortex-A55 (1.800GHz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz)
MEMORYDDR4 4GiB with 32-bit bus width
Data rate: 2640 MT/s (PC4-21333 grade)
1.2Volt low power design
STORAGE1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
NETWORKING1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
– Realtek RTL8211F (Ethernet transceiver)
– LED indicators
* Green LED: Flashing by data traffics at 100Mbps connection
* Amber LED: Flashing by data traffics at 1000Mbps connection
VIDEO1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
AUDIO1 x HDMI digital output
COOLERPassive heatsink ( 40x32x10 mm ) on the CPU of PCB board
Bearing : Hydraulic Bearing FAN
– Rated Voltage : 5V
– Rated Current : 0.2A
– Max Speed RPM : 2000RPM
– Air Flow CFM : 33
– Air Pressure (In H2O) : 0.08
– Noise Level(dBA) : 26.5
– Dimension : 92X92X25MM
– Wire & Connector : 150mm, 4pin 1.25mm pitch
EXTERNAL I/O1 x USB 2.0 host port
1 x Debug serial console (UART)
2 x SATA Connectors
OTHER FEATURESIR receiver for remote controller
System LED Indicators:
– Red (POWER) – Solid light when DC power is connected
– Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
POWER1 x DC jack : outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm
DC input : 14.5V ~ 15.5V
– DC 15V/4A power adaptor is recommended. Sold separately.
Power consumption with two ST2000DM006 HDDs :
– IDLE(with HDD in spin-down) : ≃ 5.88W
– Active(using SAMBA): ≃ 15.59W
– Suspend: ≃ 0.29W

Odroid HC4-P Kit [90000]

  • Brand: Hard Kernel
  • Product Code: Odroid HC4-P Kit
  • Availability: In Stock
  • 126.65€

  • Ex Tax: 103.81€